Current Position:Home > Products > Power Supply & Controller > LED ControllerLED Controller

T1000S Digital LED Controller

T1000S Digital LED Controller:
1.can control 2048 pixel
2.DC5V/DC7.5V-24
3.led string, strip, pixel led
4. LEDEditor software

  • T1000S Digital LED Controller:
    1. 256 Gray,Gamma correction processing software.
    2. Support the rules and special-shaped handle.
    3. Controller, a port output, may bring 1024/2048 light.
    4. Off-line control, play back content stored in the SD card
    5. T-1000C store a maximum of 16 documents

    Videohttps://www.youtube.com/watch?v=JWOI-ehVvXs

    Support IC type

    Module in LedEdit software

    Pixel numbers

    remark

    LPD6803,D705,1101,6909, 6912

    T-1000-6803

    2048 pixel

     

     

    LPD8806,LPD8809

    T-1000-8806

    2048 pixel

     

    TM1803,TM1804,TM1809,TM1812

    T-1000-TM

    2048 pixel

    TM1804 and TM1809

    low speed and high speed

    TM1903TM1904TM1909TM1912

    T-1000-TM19

    2048 pixel

     

    UCS6909UCS6912UCS7009UCS5903

    T-1000-UCS-32

    2048 pixel

     

    UCS1903UCS1909UCS1912

    T-1000-UCS-256

    2048 pixel

    low speed and high speed

    UCS3903

    T-1000-UCS-1024

    2048 pixel

     

    DMX512

    T-1000-DMX

    170/512 pixel

    Compatible DMX512

    WS2801,WS2803

    T-1000-WS

    2048 pixel

     

    WS2811

    T-1000-WS2811

    2048 pixel

    low speed and high speed

    DS189

    T-1000-DS189

    2048 pixel

     

    TLS3001,TLS3002TLS3008

    T-1000-TLS

    * pixel

     

    P9813

    T-1000-P9813

    2048 pixel

     

    SM16715

    T-1000-SM16715

    2048 pixel

    low speed and high speed

    SM16716

    T-1000-SM16716

    2048 pixel

     

    BS0901,BS0902

    T-1000-0901

    2048 pixel

     

    BS0815

    T-1000-0815

    2048 pixel

     

    Note:
    Controller on the SD card can not be hot-swappable, plug the SD card every time, you must first disconnect the power supply controller
     
    Question 1: After power, the T-1000 ERROR indicator has been flashing without display output   
    Answer: The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:
    a .SD card is empty, with no effect file
    b .The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file  led       
    c .SD card did not format to FAT before copy effect files
    d .Please check the supply power voltage, the controller can be individually powered to exclude power reasons
    f .Changing the SD card and then test to exclude the possibility of a bad SD card
     
    Question 2: The controller is powered on, the indicator is normal, but no effect change in lighting 
    Answer: The reasons for this are as follows: 
    A. Check if the lighting′s signal line and the controller connected correctly
    B.If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lighting′s and the controller′s ground together
    C.check if the model chose during making display files on the SD card match the chips used in the lighting



  • T1000S Digital LED Controller:
  • RF SD Card DMX Sender PC DMX512 Emulational Digital LED Controller WiFi Signal Dot Controller RF Touch 8key Controller RF Touch 8key Controller Waterproof RF LED Controller 24V RF Controller LED Constant Voltage 24V Controller LED RF 3CH LED Controller Audio RF Controller LED IR 44-Key LED Controller RF Synchronization Controller
  • Company Name:
    *Your Name:
    *Phone:
    MSN&Skype:
    *E-mail:
    Website:
    Please select form the list below:
    Contacted us before? YES NO
    *Message:
    Verification Code:
  • Tel

  • +86-755-29405686